The OBDY is an OBDII 16-Pin Y-Splitter kit with twelve mounting brackets, connects the VX60 device to most light-duty and medium-duty vehicles internationally. The OBDII contains the mounting adapters listed below:
Adapters
| 1 | | North American Flange MountFordGMChrysler | 7 | | European Latch & SnapFiatCitroënPeugeot |
|---|
| | | | | |
| 2 | | North American Extended Flange MountFord | 8 | | VW Snap-InVolkswagenAudiBentleyPorscheSkodaSEAT |
| | | | | |
| 3 | | North American Snap-In MountChrysler | 9 | | BMW Slide & LockBMW |
| | | | | |
| 4 | | North American Slide & Lock MountFordGM | 10 | | Ford Round Snap-InFord |
| | | | | |
| 5 | | European Lock MountMercedesBMWIveco | 11 | | Iveco Slide & LockMAN / DAF |
| 6 | | Asian Snap-InToyotaHyundaiKiaFordHondaIveco | 12 | | Volvo Slide MountVolvo |
Installation Instructions
| 1 | Remove the in-vehicle OBDII connector from its slot. | |
|---|
| 2A | Attach the female universal core connector (short end) of the harness to the appropriate adapter (see Adapters section above) matching the required installation.Note: For installation in Fiat, Citroen, or Peugeot, please refer to the European Latch & Snap installation instructions below.Note: For installation in Ford, please refer to the Ford Round Snap-in below. | |
| 2B | Secure the adapter in place using the provided metal clips. Please ensure the metal clips latch into the adapter. | |
| 2C | Fasten the female universal core connector (short end) of the harness to the vehicle’s OBDII slot and secure in place using either screws or the plastic clips on the adapters. | |
| 3 | Connect the VX60 device to the female universal core connector (long end) of the harness. | |
| 4 | Connect the male OBDII harness connector to the vehicle's OBDII connector removed in Step 1. | |
Completed Setup
European Latch & Snap
Replace Step 2 of the standard installation instructions with the following steps for Fiat, Citroën or Peugeot vehicles using the European Latch & Snap adapter.
| 1 | Slide the European Latch & Snap all the way to the back of the core connector. | |
|---|
| 2 | Insert the small snap adapter onto the wire behind the core connector. | |
| 3 | Slide the small snap adapter from the back of the harness. Ensure that the European Latch & Snap is securely interlocked. | |
Ford Round Snap-In
Replace Step 2 of the standard installation instructions with the following steps for Ford vehicles using the Ford Round Snap-In adapter.
| 1 | Slide the Ford Round Snap-In all the way to the back of the core connector. | |
|---|
| 2 | Using the insert/removal tool, secure the adapter in place using the provided metal clips. Please ensure the metal clips latch into the adapter. | |
Securing the OBDY to the Ford OBDII Module
Use two zip ties to secure the OBDY to the factory Ford OBDII module shown above.
✱
NOTE: Over tightening the zip tie may cause damage to the harness connector.
The metal clips used to secure the adapters can be inserted by hand — except for the Ford Round Snap-In (#10) adapter. The Ford Round Snap-In adapter requires the use of the insertion end of the insert/removal tool included with the harness kit. The removal of clips requires the use of the removal end of the insert/removal tool.
| Insert | Remove |
|---|
| |
| Attach the required adapter to the core connector of the harness and secure the metal clips in place with your hands. | Remove the metal clips from the adapter by pulling them off using the removal end of the insertion/removal tool. |
Updated on: 20/05/2025
